quick:gitlab_setup
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
quick:gitlab_setup [2021/02/18 10:57] bbarsch created |
— (current) | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Procedure to update user db code ====== | ||
| - | |||
| - | |||
| - | ===== Clone the userdb code from the Gitlab Repo===== | ||
| - | 1. Go to the directory you want to clone the repo to | ||
| - | |||
| - | |||
| - | 2. Go to the repo in Gitlab and copy the ssh link: | ||
| - | < | ||
| - | git@git: | ||
| - | </ | ||
| - | |||
| - | 3. Note that git should be pointing to scp and not lengau, therefore in my .ssh/config file git2 points to scp so I use: | ||
| - | git clone git@git2: | ||
| - | |||
| - | |||
| - | 4. Open your IDE, using sublime, and make changes to the code. | ||
| - | |||
| - | |||
| - | 5. Save the code | ||
| - | |||
| - | |||
| - | 6. Next step is to push the code | ||
| - | |||
| - | |||
| - | |||
| - | ===== Push the code back to Gitlab ===== | ||
| - | |||
| - | 1. Update, add, delete code and files. Then go to that directory you did the clone from and say: | ||
| - | |||
| - | git status | ||
| - | |||
| - | 2. this should show something is modified, and recommends you do: | ||
| - | |||
| - | git add . | ||
| - | |||
| - | |||
| - | 3. And check with git status again that it has been added | ||
| - | |||
| - | |||
| - | 4. Then do a commit: | ||
| - | |||
| - | |||
| - | git commit -m " | ||
| - | |||
| - | 5. Then lastly push the code to gitlab: | ||
| - | |||
| - | git push | ||
| - | |||
| - | maybe asked for a password if you didn't do ssh-copy-id, | ||
| - | to not be asked for password do ssh-copy-id to scp (as shown in the previous section) | ||
| - | |||
| - | Next we need to update the user database | ||
| - | |||
| - | ===== Update the userdb server ===== | ||
| - | |||
| - | 1. Login in to the cluster (login2) by using the following command. (replace bbarsch with your username) | ||
| - | |||
| - | ssh bbarsch@lengau.chpc.ac.za | ||
| - | |||
| - | 2. Then ssh to users (Password is P@...): | ||
| - | |||
| - | ssh users2.chpc.ac.za | ||
| - | |||
| - | 3. Login as root user (superuser...note you need admin permission): | ||
| - | |||
| - | sudo su - | ||
| - | |||
| - | 4. Connect to chpc: | ||
| - | |||
| - | su - chpc | ||
| - | |||
| - | 5. Go to the user database directory: | ||
| - | |||
| - | cd protea_database/ | ||
| - | |||
| - | 6. Check the git status if any changes exist: | ||
| - | |||
| - | git status | ||
| - | |||
| - | 7. Downloads commits, files, and refs from a remote repository into your local repo by using git fetch: | ||
| - | |||
| - | git fetch | ||
| - | |||
| - | 8. Check if any local changes exist: | ||
| - | |||
| - | git stash | ||
| - | |||
| - | 9. Pull any changes from the repo: | ||
| - | |||
| - | git pull | ||
| - | |||
| - | 10. Pull any changes from submodules (helpdesk) linked to this repo: | ||
| - | |||
| - | git submodule update | ||
| - | |||
| - | 11. Get back in to root user by logging out from chpc using: | ||
| - | |||
| - | ctrl+d | ||
| - | |||
| - | 12. Restart the gunicorn service: | ||
| - | |||
| - | systemctl restart gunicorn.service | ||
| - | |||
| - | 13. Start ngninx: | ||
| - | |||
| - | systemctl start nginx | ||
| - | |||
| - | 14. Flush redis: | ||
| - | |||
| - | redis-cli flushall | ||
| - | |||
| - | 15. Close the terminal and go to the users2 site on a browser to see changes: | ||
| - | |||
| - | users2.chpc.ac.za | ||
| - | |||
| - | - Note to do the same for usersdev you must tunnel in as its internal, use the command: | ||
| - | |||
| - | ssh -N -L 8888: | ||
| - | |||
| - | - then go to localhost: | ||
| - | |||
/app/dokuwiki/data/attic/quick/gitlab_setup.1613638639.txt.gz · Last modified: 2021/12/09 16:42 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
